本月特價 熱賣產品 貨到付款 現(xiàn)場演示 延長保修 終身維修
|
Specifications |
Model 2160A |
|
VERTICAL AMPLIFIERS (CH 1 and 2) | |
|
Sensitivity |
5mV/div to 1V/div x 5mag |
|
Attenuator |
1-2-5 sequence, plus x 5 gain step. Vernier control provide fully adjustable sensitivity between steps range 1/1 to at least 1/2.5 |
|
Accuracy |
+-3%, 5mV to 5V/div; +-5%, 1 mV, 2mV/div |
|
Input Impedance |
1MΩ +-2% |
|
Input Capacitance |
25 pF +-10% |
|
Frequency Response |
DC to 60 MHz |
|
Rise Time |
5.8ns (Overshoot <= 5%) |
|
Operating Modes |
CH1, CH2, Dual, Alternate Chop |
|
Polarity Reversal |
CH 2 invert |
|
Maximum Input Voltage |
400V (DC + AC Peak), 800 VAC p-p |
|
SWEEP SYSTEM | |
|
Sweep Display Modes |
Main, Mix, Delay |
|
Hold Off Time |
5:1 continuously variable |
|
Main Sweep | |
|
Sweep Speed |
0.1us/div. to 2.0s/div. in 1-2-5 sequence, 23 steps |
|
Accuracy |
+-3% |
|
Variable Time Control |
5:1, uncalibrated, continuously variable between steps |
|
Sweep Magnification |
10 x, +-10%, extended sweep speed up to 10ns/div |
|
Delay Sweep | |
|
Sweep Speed |
0.1us/div. to 2.0s/div. in 1-2-5 sequence, 23 steps |
|
Accuracy |
+-3% |
|
Sweep Magnification |
10 x, +-10%, extended sweep speed up to 10ns/div |
|
Delay Time Position |
Variable control to locate desirable waveform for extending |
|
Triggering | |
|
Trigger Coupling |
AUTO, NORM, TV-V, TV-H |
|
Trigger Source |
CH1, CH2, ALT, EXT, LINE |
|
Slope |
+/- |
|
HORIZONTAL AMPLIFIER | |
|
(Input through channel 2 input) | |
|
X-Y Mode |
CH 1: Y axis. CH 2: X axis |
|
Sensitivity |
Same as vertical channel 2 |
|
Accuracy |
+-3%, Y axis: +-5% X axis |
|
Input Impedance |
Same as vertical channel 2 |
|
Frequency Response |
DC: DC to 1 MHz (-3 dB). AC: 5 Hz to 2 MHz (-3 dB) |
|
X-Y Phase Difference |
3 0 at 50 kHz |
|
Maximum Input Voltage |
Same as vertical channel 2 |
|
CH 2 Output (on rear panel) | |
|
Output Voltage |
50 mV/div (nominal into 50Ω load) |
|
Output Impedance |
Approximately 50 Ω |
|
Frequency Response |
20Hz to 60MHz, -3dB into 50V |
|
CRT | |
|
Type |
6-inch rectangular with internal graticule |
|
Display Area |
8x10div (1 div = 1 cm) |
|
Accelerating Voltage |
12k |
|
Phospor |
P31 |
|
Scale Illumination |
Continuously variable |
|
Trace Rotation |
Electrical, front panel adjustable |
|
COMPONENT TESTER | |
|
Components Tested |
Resistors, capacitors, inductors, and semiconductors |
|
Test Voltage |
6V rms maximum (open) |
|
Test Current |
11 mA maximum (shorted) |
|
Test Frequency |
Line frequency (60 Hz in USA) |
|
Other Specifications | |
|
Cal/Probe Compensation Voltage |
2.0V p-p +-2% square wave, 1 kHz nominal |
|
Sweep Output |
TTL level allows synchronization of external equipment with scope sweep |
|
Intensity Modulation | |
|
Input Signal |
TTL level, intensity increasing with more negative levels |
|
Input Impedance |
Approx. 1kΩ |
|
Usable Freq. Range |
DC to 5MHz |
|
Maximum Input Voltage |
5V (DC + AC peak) |
|
Environment | |
|
Within Specified Accuracy |
50 0 to 95 0 F (10 0 to 35 0 C), 85% maximum RH |
|
Full Operation |
32 0 to 122 0 F (0 0 to +50 0 C), 10 - 80% RH |
|
Storage |
-22 0 to 158 0 F (-30 0 to +70 0 C), 10-90% RH |
|
Power Requirements |
110/120/220/240 V +- 10%, 50/60 Hz |
|
Dimensions (HxWxD) |
12.76 x 15.68x5.2 (324x398x132 mm) |
|
Weight |
16.75 lbs. (7.6 kg) |
|
Three Year Warranty | |
|
Accessories | |
|
SUPPLIED: Instruction Manual, Two PR-33A x1/x10 Probes or equivalent, AC Power Cord, Spare Fuse OPTIONAL: PR-32A Demodulator Probe, PR-37A x1/x10/REE Probe, PR-100Ax100 Probe, PR-55 High Voltage x1000 Probe, LC-210A Carrying Case | |
分享儀器
境生態(tài)檢測儀器/ca41射頻電場場強計.jpg)
隱藏對比框