TY10

Bitumastic50煤焦油密封涂料

ZX21

訂貨號：ZY351246 品牌：英國密析爾MICHELL 產 地：英國 市場 價：折扣價：發貨周期：現貨或5天內

加入收藏

打印產品信息

產品評價

加入對比

分享到：分享儀器

本月特價

熱賣產品

貨到付款

現場演示

延長保修

終身維修

產品描述技術方案相關儀器最新上架商品咨詢使用評價

Selection & Specification Data

Generic	Coal Tar
Description	Ultra-high build, single-component coal tar mastic for protecting steel and concrete substrates subject to aggressive conditions and for below grade damp proofing requirements.
Features	Application up to 30 dry mils (750 microns) in a single coat. Self priming, single-coat capabilities. Excellent corrosion resistance. Complies with MIL-C-18480-B and Bureau of Reclamation CA50 specifications.
Color	Black (0900)
Finish	Low gloss.=
Primers	Self-priming
Topcoats	Not recommended
Dry Film Thickness	18.0 mils (450 microns) in one or two coats. Total dry film thickness less than 12 mils (300 microns) or in excess of 30 mils (750 microns) not recommended.
Solids Content	By volume: 68% ± 2%
Theoretical Coverage Rate	1090 mil ft2 (26.7 m2/l at 25 microns). Allow for loss in mixing and application
Nominal VOC Values	As supplied: 3.0 lbs./gal (360 g/l) Thinned: 12 oz/gal w/ Thinner #10, 3.5 lbs./gal (417 g/l)
Dry Temperature Resistance	Continuous: 350°F (177°C) Non-continuous: 400°F (204°C)
Wet Temperature Resistance	Immersion temperature should not exceed 120°F (49°C).
Limitations	Do not use for potable water requirements.

Substrates & Surface Preparation

General	Surfaces must be clean and dry. Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating.
Steel	Immersion: SSPC-SP10 Non-Immersion: SSPC-SP6 for maximum protection. SSPC-SP2 or SP3 as minimum requirement. Surface Profile: 2.0-3.0 mils (50-75 micron)
Galvanized Steel	Non-Immersion: Sweep blast to roughen surface and produce a 1.0-2.0 (25-50 micron) profile.
Concrete	Concrete must be cured 28 days at 75° F (24° C) and 50% relative humidity or equivalent. Prepare surfaces in accordance with ASTM D4258 Surface Cleaning of Concrete and ASTM D4259 Abrading Concrete. Voids in concrete may require surfacing.

Application Equipment

Listed below are general equipment guidelines for the application of this
product. Job site conditions may require modifications to these guidelines
to achieve the desired results.

Spray Application (General)	This is a high solids coating and may require adjustments in spray techniques. Wet film thickness is easily and quickly achieved. The following spray equipment has been found suitable and is available from manufacturers such as Binks, DeVilbiss and Graco.
Conventional Spray	Pressure pot equipped with dual regulators, 3/8” I.D. minimum material hose, with 50 maximum material hose .086” I.D. fluid tip and appropriate air cap.
Airless Spray	Pump Ratio: 30:1 GPM Output: 3.0 (min.) Material Hose: 3/8” I.D. (min.) Tip Size: .023-.035” Output PSI: 2300-2500 Filter Size: 30 mesh Teflon packings are recommended and available from the pump manufacturer.
Brush & Roller (General)	Recommended for touch up and striping of weld seams and hard-to-coat areas. Avoid excessive rebrushing or re-rolling.
Brush	Use a medium bristle brush.
Roller	Use a short-nap synthetic roller cover with phenolic core.

Mixing & Thinning

Mixing	Power mix until uniform in consistency.
Thinning	May be thinned up to 12 oz/gal (10%) with Thinner #10 if needed. When used directly to concrete, thinning is required on the first coat to provide adequate “soak-in”. Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied.

Cleanup & Safety

Cleanup	Use Thinner #2 or Xylene. In case of spillage, absorb and dispose of in accordance with local applicable regulations.
Safety	Read and follow all caution statements on this product data sheet and on the MSDS for this product. Employ normal workmanlike safety precautions. Hypersensitive persons should wear protective clothing, gloves and use protective cream on face, hands and all exposed areas.
Ventilation	Warning: Vapors may cause explosion. When usedin enclosed areas, thorough air circulation must be used during and after application until the coating is cured. The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used. User should test and monitor exposure levels to insure all personnel are below guidelines. If not sure or if not able to monitor levels, use MSHA/NIOSH approved respirator.
Caution	This product contains flammable solvents. Keep away from sparks and open flames. All electrical equipment and installations should be made and grounded in accordance with the National Electric Code. In areas where explosion hazards exist, workmen should be required to use non-ferrous tools and wear conductive and non-sparking shoes.
MSDS	Bitumastic 50 Thinner #10 Thinner #2

Application Conditions

Condition	Material	Surface	Ambient	Humidity
Normal	60 to 85°F (16 to 29°C)	60 to 85°F (16 to 29°C)	60 to 90°F (16 to 32°C)	0-80%
Minimum	50°F (10°C)	50°F (10°C)	50°F (10°C)	0%
Maximum	90°F (32°C)	125°F (52°C)	110°F (43°C)	90%

Industry standards are for substrate temperatures to be above the dew point. This product simply requires the substrate temperature to be above the dew point. Condensation due to substrate temperatures below the dew point can cause flash rusting on prepared steel and interfere with proper adhesion to the substrate. Special application techniques may be required above or below normal application conditions.

Bitumastic50煤焦油密封涂料
購買提示
1.閣下有任何產品問題請致電400-663-9117.
2.中儀將提供北京、上海、深圳、南京、重慶送貨上門服務.
3.我們提供Bitumastic50煤焦油密封涂料計量送檢，在簽收前請?jiān)敿?xì)核查資料信息.
4.TY10Bitumastic50煤焦油密封涂料價格根據配置和貨期不同而不同，具體以合同為準.
5.我們?yōu)殚w下提供保修TY10Bitumastic50煤焦油密封涂料售后維修服務，提供后期技術支持.
6.閣下對TY10Bitumastic50煤焦油密封涂料使用方法等有需求時，將為閣下找到Bitumastic50煤焦油密封涂料說明書.

產品分類

建筑工程及物探

腐蝕控制產品

主推產品

同類品牌產品

三通道高斯計8030 量程0-300KG

肖氏硬度計LD0551

Condumax II

EA2-TX露點變送器

英國密析爾MICHELLBitumastic50煤焦油密封涂料

代理商廠商品牌售后維修區域：北京-上海-浙江-廣東-河南-杭州-鄭州-廣州-深圳-佛山-惠州-廈門-汕頭-臺灣-香港-天津-西安-寶雞-杭州-溫州-常州-無錫-蘇州-南京-鎮江-揚州-南通-合肥-徐州-常熟-石家莊-太原-呼和浩特-沈陽-長春-哈爾濱-南京-合肥-福州-南昌-濟南-鄭州-武漢-長沙-廣州-南寧-?？?成都-貴陽-昆明-拉薩-西安-蘭州-西寧-銀川-烏魯木齊-杭州-沈陽-長春-哈爾濱-濟南-武漢-廣州-南寧-成都-西安-大連-寧波-廈門-青島-深圳-杭州-淮安-連云港-昆山-嘉興-湖州-秦皇島-邯鄲-邢臺-保定-張家口-承德-廊坊-呼和浩特-包頭-鞍山-大慶-錦州-鐵嶺-盤錦-湛江-蕭山-遼寧-淄博-寧夏-綿陽-云南-朝陽-陜西-青海-北海-唐山-吉林-蘇州-昆山-無錫-鎮江-常州-連云港-淮安-淮陰-鹽城-揚州-徐州-宜興-江陰-南通-揚州-上海-滁州-內蒙古-新疆有銷售.北京亦莊開發區，天津?yàn)I海開發區，秦皇島經濟開發區，太原經濟開發區，呼和浩特經濟開發區，沈陽經濟開發區，營口經濟開發區，大連經濟開發區，長春經濟開發區，哈爾濱經濟開發區，虹橋經濟開發區，漕河涇開發區，連云港開發區，南通開發區，昆山開發區，南京開發區，杭州開發區，蕭山開發區，溫州開發區，寧波開發區，蕪湖開發區，合肥開發區，福州開發區，福清融僑開發區，東山開發區，南昌開發區，威海開發區，煙臺開發區，青島開發區，鄭州開發區，武漢開發區，長沙開發區，蘿崗區開發區，廣州南沙開發區，惠州大亞灣開發區，湛江開發區，南寧開發區，重慶開發區，成都開發區，貴陽開發區，昆明開發區，拉薩開發區，西安開發區，蘭州開發區，西寧開發區，銀川開發區，烏魯木齊開發區，石河子開發區，金橋出口加工區，蘇州工業園，寧波大榭開發區，廈門海滄投資區，海南洋浦開發區。

請輸入您的E-mail地址免費獲取中儀網電子雜志：

TY10Bitumastic50煤焦油密封涂料ZX21

Bitumastic50煤焦油密封涂料

Bitumastic50煤焦油密封涂料

英國密析爾MICHELLBitumastic50煤焦油密封涂料